How is interest rate risk in the banking book measured?
Interest rate risk in the banking book is the possibility that changes in market rates will adversely affect the economic value or future interest earnings of a bank's loans, deposits and other banking-book positions. It is not simply the quoted difference between one loan rate and one deposit rate. Consider a bank that makes a two-year fixed-rate loan and funds it with deposits that reprice every three months: the deposit cost can rise while the loan yield remains unchanged for a time. A rate move in the other direction or changes in different parts of the yield curve may have different effects. The Basel Committee distinguishes three important sources: mismatched timing of repricing, divergence between rates tied to different benchmarks despite similar maturities, and option effects when customers prepay or withdraw early. Measurement therefore requires more than adding up contractual maturities. It examines terms, expected cash flows, currencies, behavioural assumptions and several interest rate shocks together. There are two main lenses. An economic value measure compares the present value of relevant asset, liability and off-balance-sheet cash flows before and after a rate shock, showing the change in economic value of equity. An earnings measure estimates how net interest income might change over a stated horizon. For a simplified hypothetical example, imagine a fixed-yield loan of 100 million lira funded with the same amount of deposits repricing after three months. If the annual deposit cost rises by two percentage points at the end of month three while the loan yield stays fixed, expense increases by roughly 1.5 million lira over the remaining nine months of the first year; the full-year effect after repricing is 2 million lira. This is neither a regulatory standard-ratio calculation nor a forecast for an actual bank. Depositor behaviour, new lending, hedging and contract terms could alter the outcome. In Türkiye, the BRSA regulation on banking-book interest rate risk and the Basel standard provide institutional frameworks for scope, shock scenarios and reporting. When interpreting a reported result, check the date, currency, solo or consolidated perimeter, discounting method and model assumptions. An apparently high or low sensitivity alone does not prove that a bank is safe or profitable, or that a deposit product suits any customer; this article is not personalised investment or banking advice.
Sources of risk and two measurement perspectives
1. How does a repricing gap arise? A fixed-rate loan changes its rate only on its contractual repricing date, while a floating-rate deposit may renew earlier. For each currency, a bank sorts asset and liability cash flows into time buckets according to the next rate change as well as final maturity. If rate-sensitive liabilities exceed assets in a three-month bucket, higher rates may pressure near-term earnings. The gap is not a certain loss, however: new business volume, pricing passed to customers, the shape of the yield curve and hedging all alter the result. Collapsing several time buckets into one figure can conceal that a loan repricing after a year does not match a three-month deposit. The same nominal balance does not establish identical rate sensitivity. 2. Why examine basis and option risk separately? Two products that reprice at similar times can still follow different benchmarks, so their rates need not move together; Basel calls this basis risk. For example, a loan may follow one index while deposit pricing responds to another market condition. A customer's decision to repay a fixed-rate loan early or withdraw a term deposit before maturity can also change the timing of expected cash flows. A sight deposit is legally withdrawable immediately, yet its observed behaviour may differ; assuming that its balance will remain fixed forever is unreliable. Banks should test such assumptions by product, customer group and currency and explain how stress might change them. A table of contractual maturities alone cannot capture either of these risks. 3. How do economic value and net interest income differ? An economic value calculation discounts relevant future cash flows using interest rate curves and compares values before and after a shock. The value of a long-term fixed-rate asset may fall when rates rise, while a short-term liability's value may not move as much. An earnings approach instead examines interest income minus interest expense over a chosen horizon, such as one year. In the simplified hypothetical example of a 100-million-lira fixed-yield loan and equally sized deposits repricing after three months, a two-percentage-point rise in annual deposit cost at month three increases expense by roughly 1.5 million lira over the remaining nine months of year one; the following full-year effect would be 2 million lira if conditions stayed unchanged. This calculation excludes taxes, fees, hedges, prepayments, credit losses and balance-sheet growth; it is not the same as the economic value loss.
Scenarios, regulation and interpretive limits
4. Why apply multiple interest rate shocks? A parallel increase in rates is only one possible move. Short-term rates may change faster than long-term rates; the yield curve can steepen or flatten, and different currencies can move differently. The Basel framework calls for economic-value and earnings sensitivity to be assessed under a range of shock and stress scenarios. In each scenario, the bank reassesses contractual cash flows and behavioural assumptions, then interprets the adverse outcome alongside its risk appetite and capital. One average interest rate would obscure maturity and benchmark differences. A scenario result is a sensitivity under specified assumptions, not a probability forecast: the actual rate path and customer behaviour can depart from it. Repeating the calculation with alternative reasonable assumptions helps reveal model dependence. 5. What does standard measurement in Türkiye require? The BRSA regulation on banking-book interest rate risk establishes rules for calculation and assessment under a standard shock method. It addresses the reporting period, currency separation, a standard ratio related to own funds, and records concerning maturities, scope and discounting assumptions that banks must maintain. A regulatory reporting form is not a one-line ratio an analyst can recreate merely by subtracting annual deposit expense from interest income. The effective date and any amendments to the relevant rule should be checked in the published BRSA text when it is used. Solo and consolidated figures or different currencies should not be mixed. A regulatory limit should not be mistaken for a ceiling on each product's interest rate or the probability that an individual depositor will lose money. 6. What are the measurement limits and correct uses? The result depends on modelling choices: how long deposits are expected to remain, when loans are prepaid, whether new transactions replace maturing ones, and which curve discounts cash flows. An economic-value effect does not map one-for-one into accounting profit; a net-interest-income outlook also omits credit losses, market liquidity and many other capital risks. Derivative hedges can reduce some gaps while introducing counterparty, basis and operational risks. Compare institutions only after checking the reporting date, currency, book perimeter, shock size, discounting and behavioural assumptions. A low sensitivity ratio alone does not prove bank safety, nor does a high ratio establish that a loss will certainly occur. Current BRSA disclosures and the bank's audited notes should be read together before drawing conclusions.